Dị ka a maara nke ọma, reaming bụ usoro ikpeazụ na usoro oghere.Ọ bụrụ na ụfọdụ ihe na-emetụta ya, ọ ga-abụ na ngwaahịa emechara tozuru oke ga-aghọ ihe mkpofu ozugbo.Ya mere, gịnị ka anyị kwesịrị ime ma ọ bụrụ na anyị enwee nsogbu?Ngwá ọrụ ịkpụ OPT ahazila ụfọdụ okwu na usoro na-ebilite na ngwa bara uru nke Reamer, na-atụ anya na ị nwere ike nweta nghọta ụfọdụ n'isiokwu ahụ.
1. Ogbenye adịghị ike nke oghere dị n'ime
ihe kpatara ya
1.The ọnwụ ọsọ dị oke elu.
2.Nhọrọ nke Ịcha mmiri na-ekwesịghị ekwesị.
3.The isi deviation n'akuku nke reamer dị oke ibu, na mbelata ọnụ nke reamer adịghị n'otu gburugburu.
4.The reaming allowance bụ oke ibu, na-ezighị ezi ma ọ bụ obere, na mpaghara elu na-adịghị reamed.
5.The siwing deviation nke ịcha akụkụ nke reamer karịrị ndidi, ọnwụ ọnụ adịghị nkọ, na elu bụ ike ike.
6.The ọnwụ ọnụ nke reamer bụ oke obosara.
7.Poor mgbawa mwepụ n'oge reaming.
8.Ngabiga oke iyi nke reamer.
9.The reamer na-echihịa, na-ahapụ burrs ma ọ bụ chipping na nsọtụ.
10.Enwere mkpọkọta irighiri ihe n’ọnụ ọnụ.
11.Due ka ihe mgbochi ihe, ọ bụghị adabara efu ogo ma ọ bụ na-adịghị mma rake angle reamers.
Usoro nzaghachi
1. Belata ịcha ọsọ.
2. Họrọ Ịcha mmiri dị ka ihe nhazi si dị.
3. Belata isi akụkụ dị iche iche nke ọma ma gwerie ọnụ nke ọma.
4. Belata ego nnabata nke ọma.
5. Meziwanye izi ezi na ịdị mma nke ọnọdụ oghere dị n'okpuru tupu ịghaghachi ma ọ bụ welie ikike ịgha mkpụrụ.
6. Ghichaa obosara nke eriri agụba.
7. Belata ọnụ ọgụgụ nke ezé na reamer dị ka kpọmkwem ọnọdụ, dịkwuo ohere maka mgbawa na-ejide uzo, ma ọ bụ na-eji a reamer na a agụba ọchịchọ n'akuku iji hụ na ire mgbawa mwepụ.
8. Dochie reamer mgbe niile ma wepụ ebe a na-egweri n'oge ị na-egweri agụba.
9. N'oge egweri, ojiji, na njem nke reamer, ekwesịrị ịme ihe nchebe iji zere nkukota.
10. Maka reamer mebiri emebi, were mmanu mmanu mee ya ma obu dochie ya.
2. Ime oghere okirikiri
ihe kpatara ya
1. The reamer dị oke ogologo na enweghị isi ike, na-akpata vibration n'oge reaming.
2. The isi deviation n'akuku nke reamer dị oke obere.
3. Mbelata ọnụ nke reamer dị warara.
4. Oke oke ego nnabata.
5. E nwere notches na cross oghere n'elu nke n'ime oghere.
6. Enwere oghere ájá na oghere n'elu oghere ahụ.
7. The spindle amị bụ rụrụ, ọ dịghị ndu aka uwe, ma ọ bụ nwechapụ n'etiti reamer na ntuziaka aka uwe dị oke ibu, ma ọ bụ workpiece bụ oruru mgbe mwepụ n'ihi na uko clamping nke mkpa-walled workpieces.
Usoro nzaghachi
1. Reamers na-ezughị ezu rigidity nwere ike iji reamers na-enweghị nha nha nha nha, na echichi nke reamer kwesịrị iji isiike njikọ dịkwuo isi deviation n'akuku.
2. Họrọ eru reamers na ịchịkwa oghere ọnọdụ ndidi nke tupu nhazi usoro.Iji reamers pitch na-ahaghị nhata na iji ogologo aka na aka nkenke ntuziaka;Họrọ oghere ndị tozuru etozu.
3.Mgbe ị na-eji nha nha ụda reamers ka ream ọzọ kpọmkwem oghere, na spindle nwechapụ nke igwe ngwá ọrụ kwesịrị gbanwee, na kwesịrị ekwesị nwechapụ nke ndu aka uwe kwesịrị elu ma ọ bụ kwesịrị ekwesị clamping ụzọ kwesịrị iji belata clamping ike.
3. The centerline adịghị ogologo
ihe kpatara ya
1. The mkpọpu di iche iche tupu reaming, karịsịa mgbe aperture bụ obere, enweghị ike imezi mbụ ekwe n'ihi na ogbenye rigidity nke reamer.
2. The isi deviation n'akuku nke reamer bụ oke ibu;Nduzi na-adịghị mma na-eme ka ọ dịrị onye reamer mfe ịpụ na ntụzịaka n'oge ịghagharị.
3. Cone tụgharịa nke akụkụ ịkpụ dị oke ibu.
4. Reamer na-agbanwe na oghere dị na oghere na-akwụsịtụ.
5.Mgbe a na-emegharị aka, a na-etinye ike dị ukwuu n'otu ụzọ, na-amanye reamer ka ọ gbadaa n'otu njedebe, na-emebi ogo 5 kwụ ọtọ nke reaming.
Usoro nzaghachi
1. Mụbaa usoro ịgbasa ma ọ bụ oghere na-agwụ ike iji dozie oghere.
2. Belata isi ngbanwe akụkụ.
3. Gbanwee reamer kwesịrị ekwesị.
4. Dochie reamer na akụkụ na-eduzi ma ọ bụ akụkụ ịkpụ ogologo.
4. Mmụba na oghere
ihe kpatara ya
1. The imewe uru nke mpụta dayameta nke reamer bụ oke ibu ma ọ bụ e nwere burrs na mbepụ ọnụ nke reamer.
2. Ọsọ nke ịkpụ dị oke elu.
3. Ọnụego nri na-ezighi ezi ma ọ bụ ikike ijikwa oke.
4. The isi deviation n'akuku nke reamer bụ oke ibu;The reamer na-ehulata.
5. Enwere mgbawa mgbawa na-ejikọta ya na njedebe nke nkwụsị nke hinge.
6. Mgbe ị na-egweri, ngbanwe nke swing nke mgbụsị akwụkwọ hinge karịrị nnabata.
7. Nhọrọ nke Ịcha mmiri adịghị mma.
8. Mgbe ị na-etinye reamer, a naghị ehicha elu nke cone ahụ site na mmanụ mmanụ ma ọ bụ na-enwe ọnya na ọnya n'elu cone.
9. A na-ewepụ ọdụ ọdụdụ nke taper ahụ ma na-etinye aka na taper nke taper ahụ mgbe etinyere ya n'ime spindle igwe.
10. A na-ekpu ekwo ekwo ekwo ma ọ bụ n’okirikiri kpụrụ akpụ apụọla nke ukwuu ma ọ bụ mebie.
11. Onye na-ese n’elu mmiri anaghị agbanwe agbanwe.
12. Mgbe axis dị iche na workpiece na aka reaming, ike dị n'aka abụọ na-ezighị ezi, na-eme ka reamer na-emegharị aka ekpe na aka nri.
Usoro nzaghachi
1. The imewe uru nke mpụta dayameta nke reamer bụ oke ibu ma ọ bụ e nwere burrs na mbepụ ọnụ nke reamer.
2. Ọsọ nke ịkpụ dị oke elu.
3. Ọnụego nri na-ezighi ezi ma ọ bụ ikike ijikwa oke.
4. The isi deviation n'akuku nke reamer bụ oke ibu;The reamer na-ehulata.
5. Enwere mgbawa mgbawa na-ejikọta ya na njedebe nke nkwụsị nke hinge.
6. Mgbe ị na-egweri, ngbanwe nke swing nke mgbụsị akwụkwọ hinge karịrị nnabata.
7. Nhọrọ nke Ịcha mmiri adịghị mma.
8. Mgbe ị na-etinye reamer, a naghị ehicha elu nke cone ahụ site na mmanụ mmanụ ma ọ bụ na-enwe ọnya na ọnya n'elu cone.
9. A na-ewepụ ọdụ ọdụdụ nke taper ahụ ma na-etinye aka na taper nke taper ahụ mgbe etinyere ya n'ime spindle igwe.
10. A na-ekpu ekwo ekwo ekwo ma ọ bụ n’okirikiri kpụrụ akpụ apụọla nke ukwuu ma ọ bụ mebie.
11. Onye na-ese n’elu mmiri anaghị agbanwe agbanwe.
12. Mgbe axis dị iche na workpiece na aka reaming, ike dị n'aka abụọ na-ezighị ezi, na-eme ka reamer na-emegharị aka ekpe na aka nri.
5. Enwere ọnụ n'elu oghere dị n'ime
Ihe kpatara ya
1. Oke oke ego nnabata.
2. The ọnwụ akụkụ nke reamer bụ oke ibu.
3. Mbelata ọnụ nke reamer dị warara.
4. E nwere pores, ájá oghere, na oke spindle runout n'elu nke workpiece.
Usoro nzaghachi
1. Belata ego maka reaming.
2. Belata azụ azụ nke ngalaba ịkpụ.
3. Ghichaa obosara nke eriri agụba.
4. Họrọ oghere ndị ruru eru.
6. Aka gbajiri agbaji
Ihe kpatara ya
1. The reamer dị oke ogologo na enweghị isi ike, na-akpata vibration n'oge reaming.
2. The isi deviation n'akuku nke reamer dị oke obere.
3. Mkpịsị aka dị warara ọnwụ ọnụ;Oke oke ego nnabata.
4. E nwere notches na cross oghere n'elu nke n'ime oghere.
5. Enwere oghere ájá na oghere n'elu oghere ahụ.
6. The spindle bear bụ rụrụ arụ, na-enweghị onye ndu aka uwe, ma ọ bụ nwechapụ n'etiti reamer na ndu aka bụ nke ukwuu, ma ọ bụ n'ihi echichi nke mkpa-walled workpieces.
7. The mwekota bụ oke uko na workpiece deforms mgbe ewepu.
Usoro nzaghachi
1. Belata ịcha ọsọ.
2. Họrọ Ịcha mmiri dị ka ihe nhazi si dị.
3. Belata isi akụkụ dị iche iche nke ọma ma gwerie ọnụ nke ọma.
4. Belata ego nnabata nke ọma.
5. Meziwanye izi ezi na ịdị mma nke ọnọdụ oghere dị n'okpuru tupu ịghaghachi ma ọ bụ welie ikike ịgha mkpụrụ.
6. Ghichaa obosara nke eriri agụba.
7. Belata ọnụ ọgụgụ nke ezé na reamer dị ka kpọmkwem ọnọdụ, dịkwuo ohere maka mgbawa na-ejide uzo, ma ọ bụ na-eji a reamer na a agụba ọchịchọ n'akuku iji hụ na ire mgbawa mwepụ.
8. Dochie reamer mgbe niile ma wepụ ebe a na-egweri n'oge ị na-egweri agụba.
9. N'oge egweri, ojiji, na njem nke reamer, ekwesịrị ịme ihe nchebe iji zere nkukota.
10. Maka reamer mebiri emebi, were mmanu mmanu mee ya ma obu dochie ya.
N'ezie, ị ga-enwerịrị ezigbo onye na-eweta ngwá ọrụ.Ngwá ọrụ ịkpụ OPT bụ onye na-ebubata ihe dị elu nke ọkachamara na mmepụta nke ọkọlọtọ / na-abụghị ọkọlọtọ dị iche iche carbide reamernaPCD reamer
Shenzhen OPT Cutting Tool Co., Ltd. otu n'ime ndị na-eduga emeputa na China, ọpụrụiche na-emepe emepe na-amị carbides na PCD diamond ngwaọrụ.
Oge nzipu: Jun-16-2023